Skip to content

Batch B06 — Toolhead: Stealthburner, Clockwork 2, Klicky

One page per step

Read this chapter one step per page — big pictures, prev/next, and the same tick marks. This page is the whole chapter in one scroll.

The Stealthburner and Clockwork 2 black parts and the Klicky probe set share one plate. The Klicky set is printed here and bagged as the alternative probe — this build fits the inductive probe, and Ch 08 Step 08.54 is where the bag is set aside, unbuilt.

Revali asleep on a spool
Twelve hours for the toolhead. Start it after dinner, inspect at breakfast. Even champions need their sleep.

Time: 12.1 h (1 plate) — PrusaSlicer 2.9.6 estimates.

Sessions: 1 plate start (~5 min hands-on, 12.1 h unattended) + ~15 min inspect and bin.

Prerequisites: Gate B passed (Step B00.7 — the hotend seat and the CW2 gear bores; the caliper and insert rows run early, on what is already on the bench). B02 (SB main body, faceplate, guidler, latch, latch shuttle, pcb spacer) and B04 feed the same assembly chapter and are not print prerequisites; the toolhead chapter also needs probe_retainer_bracket.stl from B04, fitted in Ch 07/08, not in a batch.

Printed parts

STL Repo path Qty Colour g ea Bin
stealthburner_printhead_revo_voron_front.stl Stealthburner STLs/Stealthburner/Printheads/revo_voron/ 1 Black 40.6 08-SB
stealthburner_printhead_revo_voron_rear_cw2.stl Stealthburner STLs/Stealthburner/Printheads/revo_voron/ 1 Black 15.0 08-SB
[o]_stealthburner_LED_carrier.stl Stealthburner STLs/Stealthburner/ 1 Black (opaque) 0.9 08-SB
[o]_stealthburner_LED_diffuser_mask.stl Stealthburner STLs/Stealthburner/ 1 Black (opaque) 0.3 08-SB
main_body.stl (Clockwork 2) Stealthburner STLs/Clockwork2/Direct_Drive/ 1 Black 23.7 08-CW2
motor_plate.stl (Clockwork 2) Stealthburner STLs/Clockwork2/Direct_Drive/ 1 Black 14.1 08-CW2
cw2_captive_pcb_cover.stl Nitehawk-SB STLs/ 1 Black 10.9 08-CW2
KlickyProbe_v2.stl Klicky Probes/KlickyProbe/STL/ 2 (1 + spare, per the mod's own advice) Black 2.5 spare-alt
Probe_Dock_v2.1.stl Klicky Probes/KlickyProbe/STL/ 1 Black 3.1 spare-alt
Probe_magnet_holder.stl Klicky Probes/KlickyProbe/STL/ 1 Black 2.3 spare-alt
Probe_magnet_pressfit_helper.stl Klicky Probes/KlickyProbe/STL/ 1 Black 1.6 spare-alt
Probe_pressfit_holder.stl Klicky Probes/KlickyProbe/STL/ 1 Black 4.6 spare-alt
KlickyProbe_AB_mount_v2.stl Klicky Printers/Voron/v1.8_v2.4_Legacy_Trident/v1.8_v2.4_Legacy_Trident_STL/ 1 Black 4.4 spare-alt
KlickyProbe_AB_mount_v2_holder.stl Klicky (same folder) 1 Black 1.6 spare-alt
Mount_magnet_holder.stl Klicky (same folder) 1 Black 2.3 spare-alt
Mount_magnet_pressfit_helper.stl Klicky (same folder) 1 Black 1.6 spare-alt
Mount_pressfit_holder_v2.stl Klicky (same folder) 1 Black 6.6 spare-alt
Dock_mount_fixed_v2.stl Klicky (same folder) 1 Black 22.7 spare-alt

Do not print: an ADXL mount (Nitehawk-SB has one on board); the CW2 chain anchor (kit supplies "CW2 Chain Anchor Tilted" printed).

Hardware: none.

Read first

  • Checkpoint after B06: caliper the hotend seat in the printhead front now; the Revo Voron heatsink (the glossary's Revo HF — same part, HF nozzle fitted) only arrives with the kit, so sitting it flat on its 4× M3×8 is a kit-day row. Klicky: count and bag, do not build — no magnets are pressed in this batch or anywhere else in this manual (Ch 08 Step 08.54).
  • Most commonly reprinted here: KlickyProbe_v2 — that's why two are printed, in case the option is ever taken up.
  • Hotend file choice is settled: E3D Revo Voron → the revo_voron folder, ..._rear_cw2 for Clockwork 2.
  • cw2_captive_pcb_cover is LDO's improved cable door (captive screw + external chamber thermistor); the stock alternative is Clockwork2/cable_door_for_pcb.stl if you'd rather use it.
  • Klicky dock: fixed mount chosen for simplicity. If you later add the Decontaminator purge bucket, you need Dock_sidemount_fixed_v2.stl + Dock_sidemount_left_v2.stl instead (~25 g, 1.5 h) — not printed here.
  • The Probe_*_pressfit_helper / _holder parts are jigs for pressing the 6×3 magnets in square. Print them and bag them with the set — if Klicky is ever built, a crooked magnet is a probe that doesn't repeat.

Step B06.1 — Filament prep

Do: Galaxy Black on a fresh spool #2: spool #1 holds only 133 g after B05, and this plate carries the Revo seat. Keep the stub for a clip reprint. Sheet per 00-slicer-setup § Print sheet.

check Check

Clean purge; spool #2 mounted and ≥148 g on it.

Source: print plan §4.3 — spool changes · 00-slicer-setup § Drying · Prusa KB — ASA

Step B06.2 — Load plate B06-P1

Sorting diagram, drawn from the committed project: every part numbered and filled in the colour of its bin, bin id on the part; the legend reads # · STL · bin (chapter · steps). Sort at Step B06.5.

Do: Open slicer/plates/B06-P1.3mf with File → Open Project. Do not rebuild the arrangement. Confirm the loaded objects match the Parts list and that the printhead files came from the revo_voron folder. Parts: 18 files, 19 objects, no brim in the project — 12.1 h, 148 g (PrusaSlicer 2.9.6 estimate); stealthburner_printhead_revo_voron_front; stealthburner_printhead_revo_voron_rear_cw2; [o]_stealthburner_LED_carrier; [o]_stealthburner_LED_diffuser_mask; main_body (CW2); motor_plate (CW2); cw2_captive_pcb_cover; then the Klicky set — KlickyProbe_v2 ×2; Probe_Dock_v2.1; Probe_magnet_holder; Probe_magnet_pressfit_helper; Probe_pressfit_holder; KlickyProbe_AB_mount_v2; KlickyProbe_AB_mount_v2_holder; Mount_magnet_holder; Mount_magnet_pressfit_helper; Mount_pressfit_holder_v2; Dock_mount_fixed_v2.

check Check

Printhead files confirmed from revo_voron/; the dock is the fixed variant; no brim outline in the preview.

Helper: Reads the sorting diagram legend aloud and counts the parts on it while you load.

Source: print plan §3 — the batches · 00-slicer-setup § Committed projects · 00-slicer-setup § Orientation & brim · Stealthburner printhead README

Step B06.3 — Print plate B06-P1

Do: Print with standing overrides.

check Check

Before start, Settings → Chamber Filtration reads Adv. Filtration. LED carrier, diffuser mask and magnet-holder pockets print crisp, the finest features on the plate.

tip Tip

Paused or stopped mid-plate? See When the printer stops.

pause Good stopping point · ~5 min since the last one

plate started; nothing to do until it finishes.

Source: 00-slicer-setup § Overrides · print plan §4.1 — how these numbers were produced

Step B06.4 — Inspect

Do:

  1. Now: caliper the hotend seat in the printhead front, a 20.0 mm bore (verify on bench).
  2. Now: count the 12 Klicky pieces and bag them unbuilt, labelled KLICKY — alternative probe only.
  3. Kit day: sit the real Revo heatsink in it.

check Check

Seat reads 20.0 mm ±0.15 and the Klicky bag is closed with 12 pieces, labelled.

pause Good stopping point · ~10 min since the last one

seat calipered, Klicky bag closed. Nothing pressed, no magnets, and the real heatsink is a kit-day row.

Source: print plan §5.2 — checkpoint after each batch · Ch 08 Step 08.54 — bag the Klicky set · Klicky — what to print

Step B06.5 — Sort into bins

Do:

  1. Sort the plate off its diagram: number to legend, colour to bin.
  2. Mark plate id and date on a hidden face, then print labels from the bin-labels sheet.
  3. The Klicky bag goes into spare-alt closed.

B06-P1

bin parts off this plate
08-SB — Stealthburner body, printhead, LEDs stealthburner_printhead_revo_voron_front, stealthburner_printhead_revo_voron_rear_cw2, [o]_stealthburner_LED_carrier, [o]_stealthburner_LED_diffuser_mask
08-CW2 — Clockwork 2 extruder, toolboard + USB covers main_body, motor_plate, cw2_captive_pcb_cover
spare-alt — Spares / alternates (not fitted) KlickyProbe_v2 ×2, Probe_Dock_v2.1, Probe_magnet_holder, Probe_magnet_pressfit_helper, Probe_pressfit_holder, KlickyProbe_AB_mount_v2, KlickyProbe_AB_mount_v2_holder, Mount_magnet_holder, Mount_magnet_pressfit_helper, Mount_pressfit_holder_v2, Dock_mount_fixed_v2

check Check

All toolhead parts in 08-SB / 08-CW2; the Klicky bag closed in spare-alt.

Helper: Writes the bin id and the date on the inside face of each part.

pause Good stopping point · ~10 min since the last one

toolhead parts in 08-SB and 08-CW2, the closed Klicky bag in spare-alt. No magnets pressed, no hotend fitted.

Source: print plan §9 — batch summary · print plan §2 — which parts gate which step · print/README § Bins

Checkpoint B06

  • Gate B (bore + inserts) passed before B06-P1 started
  • Hotend seat in stealthburner_printhead_revo_voron_front calipers 20.0 mm ±0.15
  • (kit day) Revo Voron heatsink sits flat in that seat, ready for 4× M3×8
  • Klicky set counted (12 pieces incl. the spare KlickyProbe_v2), bagged in spare-alt, labelled "alternative probe only — Ch 08.54", no magnets pressed
Revali passing a gate
Batch B06 printed: plate 10 of 22, 84.3 of 157.0 h. 1 gummy worm.

Common mistakes

  • Slicing the wrong hotend printhead folder (not revo_voron).
  • Building Klicky because the parts are on the bench — the kit's config, wiring and pre-terminated cable are all for the inductive probe (Ch 08.54).

Next

Assembly: Stealthburner (p.146–147, then the separate Stealthburner manual) — months from now, when the kit lands; the Klicky bag and the SB parts go into bins 08-SB, 08-CW2 and spare-alt today. Printing: B07 — Electronics bay + lighting, then B08–B10.