Batch B029 / 9

Step B02.9 — Sort into bins

Step 9 of 9 with a helper · Batch B02 — Accent parts (blue)

(no image — see text)

Do:

1. Sort each plate off its diagram: the number on a part is its legend number, the colour its bin.
2. Write bin id, plate id and date on the inside face of every _a / _b part.

Check

Every accent part in its bin with the id written on it; 11-door holds only the Handle until B10.

Helper Matches each part's number to the diagram legend and drops it in its bin.

B02-P1

bin	parts off this plate
02-Z0 — Z0 corner (front-left, _a hand)	[a]_z_drive_baseplate_a
02-Z1 — Z1 corner (rear-left, _b hand)	[a]_z_drive_baseplate_b
02-Z2 — Z2 corner (rear-right, _a hand)	[a]_z_drive_baseplate_a
02-Z3 — Z3 corner (front-right, _b hand)	[a]_z_drive_baseplate_b
07-X — X carriage halves, probe bracket, cable cover	[a]_cable_cover
08-SB — Stealthburner body, printhead, LEDs	[a]_stealthburner_main_body
10-tft — Touchscreen faceplate + mount	[a]_faceplate

B02-P2

bin	parts off this plate
04-A — A drive unit + A (right) front idler	[a]_tensioner_right
04-B — B drive unit + B (left) front idler	[a]_tensioner_left
11-fans — Fan grills, retainers, belt guards	[a]_fan_grill_a ×2, [a]_fan_grill_b ×2, [a]_fan_grill_retainer ×2, [a]_belt_guard_a ×2, [a]_belt_guard_b ×2
11-door — Clicky-Clack door	Handle

B02-P3

bin	parts off this plate
02-Z0 — Z0 corner (front-left, _a hand)	[a]_belt_tensioner_a, [a]_z_tensioner_9mm
02-Z1 — Z1 corner (rear-left, _b hand)	[a]_belt_tensioner_b, [a]_z_tensioner_9mm
02-Z2 — Z2 corner (rear-right, _a hand)	[a]_belt_tensioner_a, [a]_z_tensioner_9mm
02-Z3 — Z3 corner (front-right, _b hand)	[a]_belt_tensioner_b, [a]_z_tensioner_9mm
05-XY — XY joints, endstop pod, upper Z belt clips	[a]_endstop_pod_D2F_switch, [a]_xy_joint_cable_bridge_2hole, XY_cable_chain_bridge-Igus-3mm_backer, [a]_z_belt_clip_upper ×4
06-Z-joints — Z joints and lower Z belt clips	[a]_z_belt_clip_lower ×4
08-CW2 — Clockwork 2 extruder, toolboard + USB covers	[a]_guidler_a, [a]_guidler_b, [a]_latch, [a]_latch_shuttle
10-chains — Z cable chain anchor, guide, retainer	[a]_z_chain_retainer_bracket ×2
11-skirts — Skirt ring, keystone panel and inserts	[a]_keystone_blank_insert ×2, ldo_bestagon_insert
spare-alt — Spares / alternates (not fitted)	[a]_pcb_spacer

Tip

Print the bin labels from the bin-labels sheet. _a parts go to Z0 and Z2, _b to Z1 and Z3. The [a]_z_chain_retainer_bracket pair is fitted in Ch 10, not Ch 05.

Good stopping point · ~15 min since the last one

all three plates sorted into their eleven bins, ids written on every _a / _b part. Nothing is pressed or glued; the accent spool is off and re-sealed.

Source: print plan §9 — batch summary · print plan §2 — which parts gate which step · print/README § Bins

← PreviousStep B02.8 — Inspect

Next →Checkpoint B02