Before you start Batch B10¶
Before you start · Batch B10 — Clicky-Clack door
Time: 5.7 h (1 plate) — PrusaSlicer 2.9.6 estimate — plus the blue Handle printed back in B02.
Sessions: 1 plate start (~5 min hands-on, 5.7 h unattended) + ~10 min inspect and bin, plus the bushing and pin test on kit day.
Prerequisites: Gate A (as for B08, on the current GT2 belts) and B09. This is the last batch of the
run. B02's blue Handle joins these parts at B10.6. No bearing seat here, so Gate B is not needed.
Printed parts
| STL | Repo path | Qty | Colour | g ea | Bin |
|---|---|---|---|---|---|
Handle-Hinge_Bottom.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
1 | Black | 17.1 | 11-door |
Handle-Hinge_Top.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
1 | Black | 17.1 | 11-door |
Hinge-L-sleeve-2X.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
2 | Black | 9.0 | 11-door |
Hinge-L-solid-2X.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
2 | Black | 9.2 | 11-door |
Latch.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
1 | Black | 8.4 | 11-door |
Panel_Clip.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
1 | Black | 0.9 | 11-door |
Handle.stl |
(printed in B02, blue) | 1 | Blue | 33.7 | 11-door, from B02 |
The "2X" in the filenames means print two copies; each file contains one body. Cross-check against the mod's BOM: 6 split bushings and 4 M5×45 dowel pins = 2 door hinges + 2 handle hinges.
Because you're fitting Clicky-Clack, do not print: door_hinge_x6, handle_a_x2, handle_b_x2,
latch_x2 (Voron), nor LDO's LDO Door/ set. That also means losing the LDO kit-number nameplate — if you
want it, print LDO Door/handle_b_nameplate.stl and glue it elsewhere.
The Clicky-Clack "Blue" option is the door's aluminium frame colour, matching the blue LDO frame (survey) — visible trim around the front opening, and it sits with the blue accent parts and the black body rather than against them.
Hardware: none.
Read first
- Checkpoint after B10: sleeve bearings must tap into the hinge sleeves without splitting the part; M5×45 pin into the "solid" half should be a very tight hammer fit with ~20 mm proud. Both need the Clicky-Clack kit's hardware, so the test is on kit day.
- Most commonly reprinted here:
Hinge-L-solid-2X(split risk on the pin press). - Door swing — decide now, from where the machine will live. As designed the hinges are on the left
and the door opens from the right (
Hinge-L). Mirror bothHinge-L-*files only if the printer's left side will be against a wall; handle and latch are symmetric. PrusaSlicer 3.0 preview cannot mirror — slice this batch in 2.9.6, or mirror the STL outside the slicer. src Hinge-L-sleeve/solid-2X(55.0 mm on a 20.9×19.5 footprint) andLatch.stl(58.0 mm) carry a 5 mm brim already in the project;Handle-Hinge_*andPanel_Cliphave none. Verify in the preview, never add.
