Before you start Batch B07¶
Before you start · Batch B07 — Electronics bay + lighting
Time: 16.0 h (2 plates) — PrusaSlicer 2.9.6 estimates.
Sessions: 2 plate starts (~5 min hands-on each, 7.9 / 8.1 h unattended) + ~15 min inspect and bin.
Prerequisites: Gate A passed (Step B00.5). Nothing here has a bearing seat or rail fit. It does not depend on B01–B06 (the electronics bay is independent of the mechanical gantry); its heat-set bosses get their inserts on kit day, in Ch 09.
Printed parts
| STL | Repo path | Qty | Colour | g ea | Bin |
|---|---|---|---|---|---|
wago_221-415_mount_3by5.stl |
Voron-2 STLs/Electronics_Bay/ |
1 | Black | 10.6 | 09-bay |
lrs_200_psu_bracket_x2.stl |
Voron-2 STLs/Electronics_Bay/ |
2 | Black | 8.2 | 09-bay |
PSU_stabilizer_50mm.stl |
Voron-2 STLs/Electronics_Bay/ |
1 (verify) | Black | 4.1 | 09-bay |
usb_adapter_mount.stl |
Nitehawk-SB STLs/ |
1 (spare — kit supplies one; → spare-alt) | Black | 9.4 | spare-alt |
usb_adapter_mount_partial_cover.stl |
Nitehawk-SB-V2 STLs/ |
1 (ground-lug mount) | Black | 5.0 | 08-CW2 |
pcb_din_clip_x3.stl |
Voron-2 STLs/Electronics_Bay/ |
3 (spares — the kit supplies the 4 needed) | Black | 5.9 | 09-bay |
handlebar_spacer_x4.stl |
LDOVoron2 STLs/ |
4 | Black | 2.1 | 11-finish |
cob_light_strip_mount_100mm.stl |
LDOVoron2 STLs/COB Light Strip/ |
6 | Black | 18.1 | 10-lights |
cob_light_strip_mount_50mm.stl |
LDOVoron2 STLs/COB Light Strip/ |
2 | Black | 9.3 | 10-lights |
power_inlet_IECGS_1mm.stl |
Voron-2 STLs/Skirts/ |
1 (moved from B08 — consumed in Ch 09, not the skirts chapter; rides on B07-P1) | Black | 36.2 | 09-bay |
PSU_stabilizer_50mm (verify)
LDO Build Notes say "PAGE 169 SKIP — the kit does not use a support bracket," which most likely refers to this part. It is 4 g — print it, fit only if it's actually needed.
Do not print: raspberrypi_bracket.stl, beefy_raspberry_bracket.stl, rs25_psu_bracket.stl
(Leviathan carries the Pi, no 5 V PSU in this kit); the Leviathan bracket set or the bed WAGO mount (both
supplied printed).
Hardware: none.
Read first
- Checkpoint after B07: COB mount halves flat on the reference and closing flush on their 2× M3×6 FHCS. The Wago mount's heat-set bosses get their inserts on kit day (Ch 09), not here.
- Most commonly reprinted here:
cob_light_strip_mount_100mm— warps at the ends, check flatness on glass. - COB counts are LDO's own for a 2.4-350: 6× 100 mm + 2× 50 mm. Each STL contains a 2-piece assembly joined with 2× M3 heat-sets + 2× M3×6 FHCS — the heaviest single group of "small" parts in the build (127 g on P2 alone).
