Before you start Batch B02¶
Before you start · Batch B02 — Accent parts (blue)
Every accent part in the whole build, printed in one continuous session so the accent spool is mounted exactly once. The accent is Prusament ASA Blue, matching the blue LDO frame and the blue Clicky-Clack door over the black body. Two colour changes in the whole build: black → blue here, blue → black after. Nothing here has a press fit, so it needs Gate A only. Like every batch, it prints before the kit arrives.
Time: 21.9 h (3 plates) — PrusaSlicer 2.9.6 estimates.
Sessions: 3 plate starts (~5 min hands-on each, 7.0 / 7.3 / 7.6 h unattended) + ~20 min inspect and bin.
Prerequisites: Gate A passed (Step B00.5 — the cube; a colour change doesn't skip the calibration requirement). Gate B is not needed: no bearing seat, rail fit or insert boss on these plates is load-bearing before assembly.
Printed parts
| STL | Repo path | Qty | Colour | g ea | Bin |
|---|---|---|---|---|---|
[a]_z_drive_baseplate_a_x2.stl |
Voron-2 STLs/Z_Drive/ |
2 | Blue | 9.7 | 02-Z0, 02-Z2 (one each) |
[a]_z_drive_baseplate_b_x2.stl |
Voron-2 STLs/Z_Drive/ |
2 | Blue | 9.7 | 02-Z1, 02-Z3 (one each) |
[a]_belt_tensioner_a_x2.stl |
Voron-2 STLs/Z_Drive/ |
2 | Blue | 1.9 | 02-Z0, 02-Z2 (one each) |
[a]_belt_tensioner_b_x2.stl |
Voron-2 STLs/Z_Drive/ |
2 | Blue | 1.9 | 02-Z1, 02-Z3 (one each) |
[a]_z_tensioner_9mm_x4.stl |
Voron-2 STLs/Z_Idlers/ |
4 | Blue | 8.1 | 02-Z0–Z3, one each |
[a]_tensioner_left.stl |
Voron-2 STLs/Gantry/Front_Idlers/ |
1 | Blue | 7.4 | 04-B |
[a]_tensioner_right.stl |
Voron-2 STLs/Gantry/Front_Idlers/ |
1 | Blue | 7.4 | 04-A |
[a]_cable_cover.stl |
Voron-2 STLs/Gantry/AB_Drive_Units/ |
1 | Blue | 8.0 | 07-X |
[a]_z_chain_retainer_bracket_x2.stl |
Voron-2 STLs/Gantry/AB_Drive_Units/ |
2 | Blue | 0.6 | 10-chains |
[a]_endstop_pod_D2F_switch.stl |
Voron-2 STLs/Gantry/X_Axis/XY_Joints/ |
1 | Blue | 8.1 | 05-XY |
[a]_xy_joint_cable_bridge_2hole.stl |
Voron-2 STLs/Gantry/X_Axis/XY_Joints/ |
1 | Blue | 9.2 | 05-XY |
XY_cable_chain_bridge-Igus-3mm_backer.stl |
whopping_Voron_mods extrusion_backers/STLs/ |
1 Note: alternate to the above — fit whichever clears the Ti backers, see §Read first | Blue | 9.1 | 05-XY |
[a]_z_belt_clip_lower_x4.stl |
Voron-2 STLs/Gantry/ |
4 | Blue | 2.3 | 06-Z-joints |
[a]_z_belt_clip_upper_x4.stl |
Voron-2 STLs/Gantry/ |
4 | Blue | 2.4 | 05-XY |
[a]_stealthburner_main_body.stl |
Stealthburner STLs/Stealthburner/ |
1 | Blue | 46.5 | 08-SB |
[a]_guidler_a.stl |
Stealthburner STLs/Clockwork2/Direct_Drive/ |
1 | Blue | 3.7 | 08-CW2 |
[a]_guidler_b.stl |
Stealthburner STLs/Clockwork2/Direct_Drive/ |
1 | Blue | 2.1 | 08-CW2 |
[a]_latch.stl |
Stealthburner STLs/Clockwork2/Direct_Drive/ |
1 | Blue | 3.5 | 08-CW2 |
[a]_latch_shuttle.stl |
Stealthburner STLs/Clockwork2/Direct_Drive/ |
1 | Blue | 1.7 | 08-CW2 |
[a]_pcb_spacer.stl |
Stealthburner STLs/Clockwork2/ |
1 (spare — kit supplies one) | Blue | 0.3 | spare-alt |
[a]_belt_guard_a_x2.stl |
Voron-2 STLs/Skirts/ |
2 | Blue | 5.4 | 11-fans |
[a]_belt_guard_b_x2.stl |
Voron-2 STLs/Skirts/ |
2 | Blue | 5.4 | 11-fans |
[a]_fan_grill_a_x2.stl |
Voron-2 STLs/Skirts/ |
2 | Blue | 5.9 | 11-fans |
[a]_fan_grill_b_x2.stl |
Voron-2 STLs/Skirts/ |
2 | Blue | 5.9 | 11-fans |
[a]_fan_grill_retainer_x2.stl |
Voron-2 STLs/Skirts/ |
2 | Blue | 4.2 | 11-fans |
[a]_keystone_blank_insert.stl |
Voron-2 STLs/Skirts/ |
2 (1 used + 1 spare; LDO ships one CAT6 keystone) | Blue | 2.5 | 11-skirts |
[a]_faceplate.stl |
LDOVoronTrident STLs/BTT Pi TFT4.3 Mount/ |
1 | Blue | 6.6 | 10-tft |
ldo_bestagon_insert.stl |
LDOVoron2 STLs/ |
1 | Blue | 3.0 | 11-skirts |
Handle.stl |
whopping_Voron_mods clickyclacky_door/STLs/ |
1 | Blue | 33.7 | 11-door |
Cable-chain bridge, conditional
Fabreeko's titanium extrusion backers ship pre-tapped for the cable
chain, which may make the printed bridge unnecessary. Print both [a]_xy_joint_cable_bridge_2hole and
XY_cable_chain_bridge-Igus-3mm_backer (18 g total) and fit whichever clears at assembly. "Igus" = the
2-hole chain pattern, which is what LDO ships.
Hardware: none.
Read first
- Checkpoint after B02: guidler and latch must move freely against the CW2 body once it exists (B06) — test-fit then, not now. Check the SB main body's built-in supports came out clean and the LED pockets are crisp.
- Most commonly reprinted here:
[a]_stealthburner_main_body— the most-looked-at part in the build. [a]_stealthburner_main_bodyhas built-in supports — snap them out, don't cut.Handle.stlis 60 mm tall on a 68×19 footprint — the project already carries its 5 mm brim, and nothing else on B02-P2 has one (per 00-slicer-setup.md). You verify it in the preview; you do not add it.[a]_keystone_blank_insert×2 covers a panel with 2 slots against 1 LDO-supplied CAT6 keystone — 1 used, 1 spare.
